根据enspv510版ac与ap配置

四川托普信息职业技术学院 唐小军

一、 拓扑图

二、 实验环境：

三、 相应设备：

1.无线AP:5030, AC:6605,

2.交换：二层，s3700，三层，s5700

3.电脑：STA

四、 实现目标：

1． STA3能通过无线方式访问到三层交换机接口地址，10.23.101.2

五、 配置思路

1.配置AP、AC和周边网络设备之间实现网络互通。

2.配置AP上线。

a) 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。

b) 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。

c) 配置AP上线的认证方式并离线导入AP，实现AP正常上线。

3.配置WLAN业务参数，实现STA访问WLAN网络功能。

六、 实验过程：

1. 二层交换机配置

system-view

[HUAWEI] sysname Switch

[Switch] vlan batch 100 101

[Switch] interface Ethernet0/0/1

[Switch-Ethernet0/0/1] port link-type trunk

[Switch-Ethernet0/0/1] port trunk pvid vlan 100

[Switch-Ethernet0/0/1] port trunk allow-pass vlan 100 101

[Switch-Ethernet0/0/1] port-isolate enable

[Switch-Ethernet0/0/1] quit

[Switch] interface gigabitethernet 0/0/2

[Switch-Ethernet0/0/2] port link-type trunk

[Switch-Ethernet0/0/2] port trunk allow-pass vlan 100 101

[Switch-Ethernet0/0/2] quit

2. 三层交换机配置

system-view

[Huawei] sysname Router

[Router] vlan batch 101

[Router] interface gigabitethernet 0/0/1

[Router-GigabitEthernet0/0/1] port link-type trunk

[Router-GigabitEthernet0/0/1] port trunk allow-pass vlan 101

[Router-GigabitEthernet0/0/1] quit

[Router] interface vlanif 101

[Router-Vlanif101] ip address 10.23.101.2 24

[Router-Vlanif101] quit

3. 配置AC与其它网络设备互通

system-view

[AC6605] sysname AC

[AC] vlan batch 100 101

[AC] interface gigabitethernet 0/0/1

[AC-GigabitEthernet0/0/1] port link-type trunk

[AC-GigabitEthernet0/0/1] port trunk allow-pass vlan 100 101

[AC-GigabitEthernet0/0/1] quit

[AC] interface gigabitethernet 0/0/2

[AC-GigabitEthernet0/0/2] port link-type trunk

[AC-GigabitEthernet0/0/2] port trunk allow-pass vlan 101

[AC-GigabitEthernet0/0/2] quit

4. 在AC上配置DHCP服务器为STA和AP分配IP地址

[AC] dhcp enable

[AC] interface vlanif 100

[AC-Vlanif100] ip address 10.23.100.1 24

[AC-Vlanif100] dhcp select interface

[AC-Vlanif100] quit

[AC] interface vlanif 101

[AC-Vlanif101] ip address 10.23.101.1 24

[AC-Vlanif101] dhcp select interface

[AC-Vlanif101] quit

5. 在AC上配置AP上线

# 创建AP组，用于将相同配置的AP都加入同一AP组中。

[AC] wlan

[AC-wlan-view] ap-group name ap-group1

[AC-wlan-ap-group-ap-group1] quit

# 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。

[AC-wlan-view] regulatory-domain-profile name default

[AC-wlan-regulate-domain-default] country-code cn

[AC-wlan-regulate-domain-default] quit

[AC-wlan-view] ap-group name ap-group1

[AC-wlan-ap-group-ap-group1] regulatory-domain-profile default

Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continu

e?[Y/N]:y

[AC-wlan-ap-group-ap-group1] quit

[AC-wlan-view] quit

# 配置AC的源接口。

[AC] capwap source interface vlanif 100

6. 查看ap的mac地址做好记录以备用，并为ap设置部署名称例如area_1

7. AP具有射频0和射频1两个射频。例如AP5030DN的射频0为2.4GHz射频，射频1为5GHz射频。

[AC] wlan

[AC-wlan-view] ap auth-mode mac-auth

[AC-wlan-view] ap-id 0 ap-mac 60de-4476-e360

[AC-wlan-ap-0] ap-name area_1

[AC-wlan-ap-0] ap-group ap-group1

Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration

s of the radio, Whether to continue? [Y/N]:y

[AC-wlan-ap-0] quit

8. 保证AP上电并与AC连接，当执行命令display ap all查看到AP的“State”字段为“nor”时，表示AP正常上线。

[AC-wlan-view] display ap all

Total AP information:

nor : normal [1]

-------------------------------------------------------------------------------------

ID MAC Name Group IP Type State STA Uptime

-------------------------------------------------------------------------------------

0 00e0-fcfe-1e60 area_1 ap-group1 10.23.100.106 AP5030DN nor 0 10S

-------------------------------------------------------------------------------------

Total: 1

9. 配置WLAN业务参数，配置WPA-WPA2+PSK+AES的安全策略，密码为“a1234567”

[AC-wlan-view] security-profile name wlan-net

[AC-wlan-sec-prof-wlan-net] security wpa-wpa2 psk pass-phrase a1234567 aes

[AC-wlan-sec-prof-wlan-net] quit

# 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。

[AC-wlan-view] ssid-profile name wlan-net

[AC-wlan-ssid-prof-wlan-net] ssid wlan-net

[AC-wlan-ssid-prof-wlan-net] quit

# 创建名为“wlan-net”的VAP模板，配置业务数据转发模式、业务VLAN，并且引用安全模板和SSID模板。

[AC-wlan-view] vap-profile name wlan-net

[AC-wlan-vap-prof-wlan-net] forward-mode direct-forward

[AC-wlan-vap-prof-wlan-net] service-vlan vlan-id 101

[AC-wlan-vap-prof-wlan-net] security-profile wlan-net

[AC-wlan-vap-prof-wlan-net] ssid-profile wlan-net

[AC-wlan-vap-prof-wlan-net] quit

# 配置AP组引用VAP模板，AP上射频0和射频1都使用VAP模板“wlan-net”的配置。

[AC-wlan-view] ap-group name ap-group1

[AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 0

[AC-wlan-ap-group-ap-group1] vap-profile wlan-net wlan 1 radio 1

[AC-wlan-ap-group-ap-group1] quit

10. 配置AP射频的信道和功率,关闭射频的信道和功率自动调优功能。射频的信道和功率自动调优功能默认开启，如果不关闭此功能则会导致手动配置不生效。

[AC-wlan-view] rrm-profile name default

[AC-wlan-rrm-prof-default] calibrate auto-channel-select disable

[AC-wlan-rrm-prof-default] calibrate auto-txpower-select disable

[AC-wlan-rrm-prof-default] quit

# 配置AP射频0的信道和功率。

[AC-wlan-view] ap-id 0

[AC-wlan-ap-0] radio 0

[AC-wlan-radio-0/0] channel 20mhz 6

Warning: This action may cause service interruption. Continue?[Y/N]y

[AC-wlan-radio-0/0] eirp 127

[AC-wlan-radio-0/0] quit

# 配置AP射频1的信道和功率。

[AC-wlan-ap-0] radio 1

[AC-wlan-radio-0/1] channel 20mhz 149

Warning: This action may cause service interruption. Continue?[Y/N]y

[AC-wlan-radio-0/1] eirp 127

[AC-wlan-radio-0/1] quit

[AC-wlan-ap-0] quit

11. 验证配置结果, WLAN业务配置会自动下发给AP，配置完成后，通过执行命令display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP对应的射频上的VAP已创建成功。

12. STA搜索到名为“wlan-net”的无线网络，输入密码“a1234567”并正常关联后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线网络“wlan-net”中。

在STA3上做如下操作：