元器件交易网www.cecb2b.com
H100ISeries
Ultra-Miniature MiniDIP1W, High IsolationDC/DC Con vert ers
Electrical Specifi cations
New Models!!
Min.
5 VDC Input
4.510.821.6
12 VDC Input24 VDC Input
Typ.5.012.024.0
Max.5.513.226.40.3
AUnits%%%
100
120
±0.01
Momentary (0.5 Sec.)
±0.02
mV P - P%%/ºCVDCUnits
Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.
Key Features:
• 1W Output Power
• Miniature MiniDIP Case• 3,000 VDC Isolation
• Complies to RFI Standards• >2 MHour MTBF
• 18 Standard Models
• Industry Standard Pin-Out
Input
Parameter
Input Voltage RangeInput Filter
Reverse Polarity Input Current
Conditions
Internal Capacitor
Output
Parameter
Output Voltage AccuracyLine RegulationLoad RegulationRipple & Noise (20 MHz)Output Power ProtectionTemperature Coeffi cientOutput Short Circuit
For Vin Change of 1%Iout = 20% to 100%
Conditions
Min.
Typ.±1.0±1.2±8.0
Max.±3.0±1.5
RoHS Compliant
General
ParameterIsolation VoltageIsolation ResistanceIsolation CapacitanceSwitching FrequencyEMI/RFI
Conditions
60 Seconds500 VDC100 kHz, 1V
Min.3,0001,000
6080
100
Typ.
Max.
UnitsVDCMΩpFkHz
EN55022 A, EN55024 A, IEC 61000-4-2, IEC 61000-4-3, FCC 47 CFR Part 15 BConditions
Case
-40
Free Air Convection
RH, Non-condensing
95
%
Min.-40
Typ.+25
Max.+85+100+125
Units
ºC
Environmental
Parameter
Operating Temperature RangeOperating Temperature RangeStorage Temperature RangeCooling
ºC
ºC
MicroPower Direct
292 Page Street
Ste D
Stoughton, MA 02072USA
Humidity
Physical
Case SizeCase MaterialWeight
0.50 x 0.40 x 0.27 Inches (12.70 x 10.16 x 6.85 mm)
Non-Conductive Black Plastic (UL94-V0)
0.06 Oz (1.8g)
Conditions
MIL HDBK 217F, 25ºC, Gnd BenignConditions
5 VDC Input
Input Voltage Surge (1 Sec)Lead TemperatureInternal Power Dissipation
12 VDC Input24 VDC Input
1.5 mm From Case For 10 Sec
All Models
Min.2.0Min.-0.7-0.7-0.7
Typ.
Max.7.015.028.0260450
ºCmWVDC
Typ.
Max.
UnitsMHoursUnits
T: (781) 344-8226F: (781) 344-8481
E: sales@micropowerdirect.comW: www.micropowerdirect.com
Reliability Specifi cations
ParameterMTBF
Absolute Maximum Ratings
Parameter
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
元器件交易网www.cecb2b.com
Model Selection Guide
ModelNumberH101IH102IH103IH104IH105IH106IH111IH112IH113IH114IH115IH116IH121IH122IH123IH124IH125IH126I
Input
Voltage (VDC)NominalRange
54.5 - 5.554.5 - 5.554.5 - 5.554.5 - 5.554.5 - 5.554.5 - 5.51210.8 - 13.21210.8 - 13.21210.8 - 13.21210.8 - 13.21210.8 - 13.21210.8 - 13.22421.6 - 26.42421.6 - 26.42421.6 - 26.42421.6 - 26.42421.6 - 26.42421.6 - 26.4
Current (mA)
Full-LoadNo-Load278252672526025256252572525725116161121610916107161071610716588568558548548548
Voltage
(VDC)3.35.09.012.015.024.03.35.09.012.015.024.03.35.09.012.015.024.0
OutputCurrent(mA, Max)300.0200.0111.083.366.1.6300.0200.0111.083.366.1.6300.0200.0111.083.366.1.6
Current(mA, Min)5.04.02.02.02.02.05.04.02.02.02.02.05.04.02.02.02.02.0
Effi ciency(%, Typ)
727577787878727577787878727577787878
Fuse RatingSlow-Blow(mA)500500500500500500200200200200200200100100100100100100
Other outputs are available.Contact the factory for details at: sales@micropowerdirect.com
Notes:
1. Output load regulation is specifi ed for a load change of 20% to 100%.
2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin.3. Operation at no-load will not damage these units. How-ever, they may not meet all specifi cations.
4. The 5V, 12V and 24V input units do not require external components to operate, but the use of a low ESR capaci-tor (approximately 10 uF, ESR <1.0Ω at 100 kHz) mounted close to the converter input pins is recommended.
For 48 VDC input units, an input capacitor should always be used. Dependent upon the application, a value between 4.7 µF and 47 uF should be suffi cient.
5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating.
Derating Curve
Capacitive Load
(µF Max)220
Mechanical Dimensions
Pin Connections
Pin1457
Function-Vin+Vin+Vout-Vout
Notes:
• All dimensions are typical in inches (mm)• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the top of the unit
MicroPower Direct
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
www.micropowerdirect.com
